My New Problem

[MaitreKanter 182]

where is bryan ?

 

 

[nino-xbox 44]

where is bryan ?

 

now i am looking bryan

 

he are in the bed with vicky

 

[MaitreKanter 182]

I'm not sure but i think that it isn't necessary if you have disconnect the hard drive disc and the another module, the wii does not boot ...

 

Dear nzo, look at bushing say :

 

"If you power on the Wii, even if nothing appears on the screen, the Starlet will still start up and write to your NAND flash. It does this every few minutes. If this ever happens while you’re trying to read or write to the flash chip, your dump is toast, and the contents of the flash may be corrupted. It is NOT enough to just remote the BT or Wifi modules to keep the thing from booting"

 

[TooN 0]

 

Heu.... Je suis sorry, mais là ce serait plus "IYA"...

 

[bonx 7]

if it not Data0~GND. plz tell me where to connection it?

Hi,

 

As Maitre Kanter told you, it's the D0 trick.

This trick is intended to avoid data changes in the nand during the read process.

The mail goal of this trick is to rise an error in the very first steps of the boot process.

 

You do not need this trick if your wii is full bricked.

 

Regards

[nino-xbox 44]

BONX the rey of the débrick and jtag is back

 

[thiefstar 0]

I thought this thread had been deleted. Because I could not find this thread.

Until someone told me that my thread has been moved to here.

Thank everyone for the reply

Je croyais que ce fil a été supprimé. Parce que je n'ai pas pu trouver ce fil.

Jusqu'à ce que quelqu'un m'a dit que mon fils a été déplacé ici. : omg:

Nous remercions tous pour la réponse

 

 

to Sephi

 

are your weldings good ?

 

yes. My weldings is good. Every time I will using the multimater to check my soldering good or bad.

Oui. Mes soudures sont bonnes. Chaque fois que je l'aide de la multimater pour vérifier ma bonne ou une mauvaise soudure.

 

 

 

 

to MaitreKanter

 

it's the D0 trick..if you short D0 to ground when boot0 try to load boot1, it fail and stop....you have to do this to have correct dump.

So you have to short D0 to ground with switch or push button, hold it and press power, when the led turn green, release push button.

OK, If it's a D0 trick, I think I must skip it. Because I have never succeeded. As far as I know. In addition to bushing, no one had succeeded. Also in my last test, I did not use D0 trick, but also the success of flash bootmii.

OK, si c'est un truc D0, je pense que je dois sauter. Parce que je n'ai jamais réussi. Pour autant que je sais. En plus de douille, personne n'avait réussi. Aussi dans mon dernier test, je n'ai pas utilisé trick D0, mais aussi le succès de BootMii flash.

 

 

to xavbox

 

Dear thiefstar, sorry for the last message, we try to find solutions to you problem as quick as possible...

Thank you very much

 

 

 

to angepit

 

Je suis désolé. Je ne comprends pas le français. Je ne peux compter que sur la traduction de Google. Mais je vais essayer de google la traduction française d'une plus compréhensibles

 

to nzo

and bonx

 

Hi,

 

As Maitre Kanter told you, it's the D0 trick.

This trick is intended to avoid data changes in the nand during the read process.

The mail goal of this trick is to rise an error in the very first steps of the boot process.

 

You do not need this trick if your wii is full bricked.

 

OK, Last time I did not using the D0 trick and I successfully flash the bootmii.

So I think I do not need the D0 trick.

 

But until yesterday I still can not to solve the "block is different" problem.

When I dump out the block1 ~ 7 data then verify it, it is correct.

When I erase the block1~7 and erase veriry. and compare again the block1~7 data, it will become a "block is different"

I have tried to replace the "WE" into shorter wrie or longer wrie.

I have tried to remove the 5V Wrie.

I have tried to desoldering the nand flash, and soleing on a PCB

OK, la dernière fois je ne l'aide pas le truc D0 et je flash avec succès le BootMii.

Je pense donc que je n'ai pas le truc D0.

 

Mais jusqu'à hier, je n'arrive toujours pas à résoudre le bloc "est différent" problème.

Quand je rejette le block1 ~ 7 Les données de vérifier le prendre, il est correct.

Quand je effacer le block 1 ~ 7 et effacer veriry. et de comparer à nouveau le block1 ~ 7 données, il deviendra un «bloc est différente"

J'ai essayé de remplacer le nous »,« en wrie plus courte ou plus longue wrie.

J'ai essayé d'enlever le 5V Wrie.

J'ai tenté de dessouder le flash NAND, et soleing sur un PCB

 

 

but it still not changed.

mais c'est toujours pas changé.

 

 

 

 

My Japanese and Chinese is better. If you do not understand my English and French. I can use Japanese or Chinese to illustrate my situation. Thank you

Mon japonais et chinois, c'est mieux. Si vous ne comprenez pas mon anglais et en français. Je peux utiliser le japonais ou le chinois pour illustrer ma situation. Je vous remercie

[xavbox 0]

My Japanese and Chinese is better. If you do not understand my English and French. I can use Japanese or Chinese to illustrate my situation. Thank you

No problem, some of french members writing with strange word here

 

in which country are you ?

[thiefstar 0]

No problem, some of french members writing with strange word here

 

in which country are you ?

 

I am Taiwanese.......

Such as beans in general a small island

[bonx 7]

Hi,

I thing it's just due to the way you are using the software.

If you enter "start bloc=1" and "end bloc"=7, and then clic read

and save the data into a file, you will save seven blocs.

If you enter "start bloc=3" and "end bloc"=4, and then clic compare

using the previous file, the software will consider that the first bloc

in the data file correspond to the bloc 0 of the nand.

The "relative mode" check box changes the way the software works.

If you check it, the software will consider that the first bloc in the data file

correspond to the bloc written in "start bloc" field of the nand.

 

I know it's quite confusing.

I suggest you:

- "start bloc"=0, "end bloc"=10, read the data in a file

You can also check the "ECC" checkbox, the software will verify all the ECC data,

it's a very good way to check that the data is consistent

- "start bloc"=0, "end bloc"=10, compate to the data in a file

- "start bloc"=3, "end bloc"=4, compate to the data in a file

 

When it's done, tell me the results.

Regards