thiefstar

hi, I installed Waninkoko CFW to my PS3 Fat. and I got brick. can I unbrick it with infectus?

hi, I think if you install libusb, it will be works. I trid to test it on VMware-ubuntu, it could detect infectus. but doesn't seems correct detection nand flash. may be it's PC of I/O problem.

I'm looking forward to the new version. and hope that it can improve the read / write speed

Hi bonx, thank you for your reply. I will try it tonight. but this nand was brick. to unbrick this, only wait for boot1c of boot2 as bootmii.

Hi, the new type Mother board Motherboard I do not know this is correct or not. Nand

The reason is because my GND wire is too long (sorry) when I replace a short GND wire, it work fine for all nand flash of samsung . The strange thing, if I don't replace a short GND wire, infectus will don't work for samsung 6XX. but can work for samsung 7XX(At least I could correctly write bootmii to two Wii)

problem solved

Hi, I've tested some Wii, I got the results, I found that you can using infectus flash to Samsung nand flash memory is only [samsung 7XX]. I flashed nand flash is samsung 707 when I flash samsung 652&646. I always get update failed. If someone successfully flash samsung 6XX. Please tell me

Hello, original post: http://www.91wii.com/thread-26561-1-1.html Successful repair 003 Tools: 1024 programmer WL-TSOP48-U1 WindowsXP system WinHex Red Hat Linux 9.0 system TrueCrypt v6.3a For Linux A normal Wii Methods: The first backup the normal Wii nand to NAND.BIN take off the nand IC: hy27uf084 from the got error003 Wii motherboard Access to XP system using programmer to read it that nand into 003.bin compare the nand.bin and 003.bin with WinHex, if the agreement to conduct the next step, otherwise serious consequences. Access to Red Hat Linux 9.0 system Using TrueCrypt v6.3

I am Taiwanese....... Such as beans in general a small island

I thought this thread had been deleted. Because I could not find this thread. Until someone told me that my thread has been moved to here. Thank everyone for the reply Je croyais que ce fil a été supprimé. Parce que je n'ai pas pu trouver ce fil. Jusqu'à ce que quelqu'un m'a dit que mon fils a été déplacé ici. : omg: Nous remercions tous pour la réponse yes. My weldings is good. Every time I will using the multimater to check my soldering good or bad. Oui. Mes soudures sont bonnes. Chaque fois que je l'aide de la multimater pour vérifier ma bonne ou une mauvaise soudure. OK,

Hi, I flash Hynix nand chip and install bootmii is very easy. but flash Samsung chips is almost too hard. Last time I helped my friend flash bootmii of success. this time the same Samsung chips. I use the same wires to flash it. but I couldn't flash any data. I got block is different massege. I have followed the xavbox's diagram but I don't know where this wire connection to? it look as Data0~GND. but if I did so. I start up the infectus and try to "Detect USB", "Open", then "Ident", I will get an error that the software can't identify the nand. therefore I skiped it.

I succeed I unbricked it. yahooooooooooo~~~~ Thank you every one Thank you MaitreKanter

I want to ask a simple question can Infectus modchip programm Samsung nand chips? had Someone successfully been programmed Samsung chip? if yes. I will continue

happy new year I unbricked a hynix chip Wii. it's work fine now I just spent an hour. but my samsung chip problem still Pending resolution. if someone can tell me to what is the "supply wire" . and where it is to solder. I will try it. thanks