thiefstar 0 Posted December 25, 2009 Report Share Posted December 25, 2009 (edited) hello I cut 0~1048575 of the installed bootmii/boot2 backup filemade a new bin file, and paste write that copied data I put the new file and setting offset to 0~1048575 on the amoxiflash. and press the write bouttan.when it start to write it, that end offset value autochange for 1081343.it wrote to block0~block7, and finished. I unplug infectus USB and remove the v5 wire only. and connact AV and power cable. insert the have contains a bootmii folder of the SD card to SD slot. power on it and....it's dosen't work. I got the blue screen(no singnal) so I put the from another Wii installed bootmii/boot2 full backup file.and Challenge to write 0~1048575(1081343) again. write is done.and I make sure to it's works or not. OK. it dosen't work. so I'll edit to the full backup file of the from bricked wii.my step is.. 1.copy 135168~1048575 of the installed bootmii/boot2 full backup file.2.Paste write to full backup file of the bricked wii.3.on the NDT put the edited full backup4.write to 0~1048575(1081343) If my step have wrong. Please tell me Edited December 25, 2009 by nino-xbox hello is recomended when to open a new topic thanck's Quote Link to post Share on other sites
nino-xbox 44 Posted December 25, 2009 Report Share Posted December 25, 2009 hello you use your backup of nand.bin or an other backup of nand ??? WII are protected and doesnt work with an other nand.bin ++ Quote Link to post Share on other sites
nino-xbox 44 Posted December 25, 2009 Report Share Posted December 25, 2009 (edited) BONX member xavboxteam have à soft here : http://www.xavboxwii.com/fr/backup-nand-par-bonx.php it's an software for read or write the nand of the wii ++ Edited December 25, 2009 by nino-xbox Quote Link to post Share on other sites
MaitreKanter 182 Posted December 26, 2009 Report Share Posted December 26, 2009 Hello, you have to use the same boot2 !for example : if your wii have boot1b boot2V2, you have to flash with the same dump boot2v2... Quote Link to post Share on other sites
thiefstar 0 Posted December 27, 2009 Author Report Share Posted December 27, 2009 Hello, you have to use the same boot2 !for example : if your wii have boot1b boot2V2, you have to flash with the same dump boot2v2... ummmm maybe that's my important miss.OK, I'll try it. Thank you for always Quote Link to post Share on other sites
thiefstar 0 Posted December 27, 2009 Author Report Share Posted December 27, 2009 BONX member xavboxteam have à soft here : http://www.xavboxwii.com/fr/backup-nand-par-bonx.php it's an software for read or write the nand of the wii ++ Hi, I'm useing it the xavprog.but, whan I write the image file, I get fail always. if I select campara file.so I tried amoxiflash. thanks Quote Link to post Share on other sites
nino-xbox 44 Posted December 27, 2009 Report Share Posted December 27, 2009 yo are you used the diagramm of bonx with xavprog ??? ++ Quote Link to post Share on other sites
thiefstar 0 Posted December 27, 2009 Author Report Share Posted December 27, 2009 yo are you used the diagramm of bonx with xavprog ??? ++ Hi, I think the diagramm of bonx and Team infectus is the same as published. and I solved this compara problem. I can dump, compara, and updata complete now. but when I edit bolck3~4 and update it. I got message block3~4 different. I copy block3~4 of the installed bootmii/boot2v2 full backup file.and Paste write to the block3~4 dump file of frome bricked wiiwhen I select updata compara and press write. I got message block3~4 different. If I erase to the all nand flash data. and Write to edited full dump file(paste write installed bootmii block3~4 data). can it work fine? Quote Link to post Share on other sites
MaitreKanter 182 Posted December 27, 2009 Report Share Posted December 27, 2009 the "we" wire must be the greater.for your problem of the different block, you can try to increase the section of the supply wire. good luck Quote Link to post Share on other sites
thiefstar 0 Posted December 27, 2009 Author Report Share Posted December 27, 2009 the "we" wire must be the greater.for your problem of the different block, you can try to increase the section of the supply wire. good luck I understand what you mean. I'll try it. thanks. Quote Link to post Share on other sites
thiefstar 0 Posted December 30, 2009 Author Report Share Posted December 30, 2009 the "we" wire must be the greater.for your problem of the different block, you can try to increase the section of the supply wire. good luck Hi, I want make sure to the "supply wire" = "power wire"?if so, I couldn't found it's diagramm about the supply wire soldering point In addition to outside here. Others I can not find but I changed the "WE" wire to greater. and test flash my Samsung chip.01.dump 4095(1)02.compare 4095(1)-OK03.erase 4905-OK04.erase verify-OK 05.compare 4095(1)-NG(different)06.write and without compare-OK07.dump 4095(2)08.useing hex compare soft to compare (1) and (2) -NG 09.compare 4095(2)-OK10.erase 4905-OK11.erase verify-OK 12.compare 4095(1)-NG(different)13.compare 4095(2)-OK14.write (1) and without compare-OK15.dump 4095(3)16.useing hex compare soft to compare (1) and (3)-NG / (2) and (3)-OK(same) 17.compare 4095(3)-OK18.erase 4905-OK19.erase verify-OK 20.compare 4095(1)-NG(different)21.compare 4095(3)-OK22.write (1) and without compare-OK23.dump 4095(4)24.useing hex compare soft to compare (1) and (4)-NG / (2)(3) and (4)-OK(same) Quote Link to post Share on other sites
thiefstar 0 Posted December 30, 2009 Author Report Share Posted December 30, 2009 Sorry, I revised my mistakes 01.dump 4095(1)02.compare 4095(1)-OK03.erase 4905-OK04.erase verify-OK 05.compare 4095(1)-NG(different)06.write and without compare-OK07.dump 4095(2)08.useing hex compare soft to compare (1) and (2) -NG 09.compare 4095(2)-OK10.erase 4905-OK11.erase verify-OK 12.compare 4095(1)-NG(different)13.compare 4095(2)-NG(different)14.write (1) and without compare-OK15.dump 4095(3)16.useing hex compare soft to compare (1) and (3)-NG / (2) and (3)-OK(same) 17.compare 4095(3)-OK18.erase 4905-OK19.erase verify-OK 20.compare 4095(1)-NG(different)21.compare 4095(3)-NG(different)22.write (1) and without compare-OK23.dump 4095(4)24.useing hex compare soft to compare (1) and (4)-NG / (2)(3) and (4)-OK(same) Quote Link to post Share on other sites
thiefstar 0 Posted December 31, 2009 Author Report Share Posted December 31, 2009 happy new year I unbricked a hynix chip Wii. it's work fine now I just spent an hour. but my samsung chip problem still Pending resolution. if someone can tell me to what is the "supply wire" . and where it is to solder.I will try it. thanks Quote Link to post Share on other sites
nino-xbox 44 Posted December 31, 2009 Report Share Posted December 31, 2009 Good year 2010 to you and US WWE rules ps: WWE is my english teacher Quote Link to post Share on other sites
thiefstar 0 Posted January 3, 2010 Author Report Share Posted January 3, 2010 I want to ask a simple question can Infectus modchip programm Samsung nand chips?had Someone successfully been programmed Samsung chip? if yes. I will continue Quote Link to post Share on other sites
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.